Trans-Oceanic (TransOceanic) 8G005YT Ch= 8C40
Zenith Radio Corp.; Chicago, IL
- País
- Estados Unidos
- Fabricante / Marca
- Zenith Radio Corp.; Chicago, IL
- Año
- 1946/1947
- Categoría
- Radio - o Sintonizador pasado WW2
- Radiomuseum.org ID
- 68077
-
- alternative name: Chicago Radio Lab
Haga clic en la miniatura esquemática para solicitarlo como documento gratuito.
- Numero de valvulas
- 8
- Principio principal
- Superheterodino con paso previo de RF; ZF/IF 455 kHz
- Gama de ondas
- OM y más de dos OC
- Tensión de funcionamiento
- Red / Baterías o pilas
- Altavoz
- Altavoz dinámico (de imán permanente) / Ø 13.5 cm = 5.3 inch
- Material
- Cuero/Tela/ Plástico sobre otros materiales
- de Radiomuseum.org
- Modelo: Trans-Oceanic 8G005YT Ch= 8C40 - Zenith Radio Corp.; Chicago,
- Forma
- Portátil > 20 cm (sin la necesidad de una red)
- Ancho, altura, profundidad
- 430 x 280 x 200 mm / 16.9 x 11 x 7.9 inch
- Anotaciones
- See also the article here.
Siehe auch den Artikel hier.
Si veda anche questo articolo nel forum.
- Precio durante el primer año
- 120.00 $
- Ext. procedencia de los datos
- Ernst Erb
- Referencia esquema
- Rider's Perpetual, Volume 15 = 1947 and before
- Mencionado en
- Bryant/Cones: The Zenith Trans-Oceanic
- Otros modelos
-
Donde encontrará 4494 modelos, 4099 con imágenes y 3605 con esquemas.
Ir al listado general de Zenith Radio Corp.; Chicago, IL
Colecciones
El modelo Trans-Oceanic (TransOceanic) 8G005YT es parte de las colecciones de los siguientes miembros.
- Hannu Alho (FIN)
- John Allen (CDN)
- Jürgen Bauch (D)
- Konrad Birkner † 12.08.2014 (D)
- Gary Brandenburger (USA)
- Angelo Daniele (I)
- Jorge Ferreira da Silva (P)
- Michael Gambuzza (USA)
- Mike Melzer (AUS)
- Tullio Milanese (I)
- Bill Morris (USA)
- Vitor Oliveira (P)
- Jean Claude Pigeon † 2008 (F)
- Rich Post (USA)
- Charles Sampayo (USA)
- Giuseppe Antonio Tusini (I)
Contribuciones en el Foro acerca de este modelo: Zenith Radio Corp.;: Trans-Oceanic 8G005YT Ch= 8C40
Hilos: 3 | Mensajes: 3
First of all: do not use the mains supply. You are going to risk tubes!
Be extremely careful.
Start with a regulated 9Volt DC Lab. Power supply with current limitation (50 mA) for the series filaments and follow by measurement tube by tube. The available schematic is good enough, since it only shows a different rectifier tube which You do not need now. The filaments are in the right order, and a current limitation will safeguard. If you would shortcut some of the tubes a battery might burn the other tubes. And the mains supply gives only the correct power if everything is to order.
Konrad Birkner † 12.08.2014, 12.Nov.06
Konrad Birkner † 12.08.2014, 30.Mar.04
Konrad Birkner † 12.08.2014, 23.Mar.04