Antique radios, Old Time Radios
ECL82
|
Country:
Europe
|
|
| Identical to |
ECL82
= 6BM8
= 6PL12_MAZDA
|
| Similar
Tubes |
Normally replaceable-slightly different:
6TP6
; 6Ф3П
Different maximum ratings:
6CN8
Heater different:
LCL82
; PCL82
; UCL82
; XCL82
|
| First year |
1956
Tube leaflet collection E.Erb Analysis by original leaflets
|
| First Source
(s) |
Jun.1956 : Funkschau 1956, Heft 11
|
| Predecessor Tubes |
ECL113
ECL81
|
|
Successor Tubes
|
ECL86
|
| Base |
Noval, 9 pin miniature (USA pico-9) B9A
|
| Was used by |
Radio/TV-reception etc. |
| Filament |
Vf 6.3 Volts / If 0.78 Ampere / Indirect / Specified voltage AC/DC |
| Description |
The ECL82 is derived from the PCL82, which was designed for TV purposes. However, the ECL82 was used almost exclusively as AF pre- and output amp, although the triode section is greatly oversized for this application.
Just as the ac/dc tube PCL82, the output section of ECL82 has been designed for an anode and screen voltage of 170V.
Operating on higher voltages is also possible, however, a screen grid resistor is then required, which deteriorates the operating characteristics. Despite this drawback, the ECL82 was very often used as AF tube used because there was no alternative until it was superseded by the ECL86.
Text in other
languages (may
differ)
|
| Tube prices |
51 Tube prices (visible for members
only)
|
ECL82: Courtesy Bureau Belper (De Muiderkring, Bussum), Scan Frank Philipse
Karel De Reus †
More ...
|
ECL82: RTT 1974 (Franzis) 13. Auflage
Martin Renz
More ...
|
Just Qvigstad
|
ECL82: Telefunken Röhrenhandbuch
Wolfgang Bauer
More ...
|
Quantity of Models at Radiomuseum.org with this tube (valve, valves, valvola, valvole, válvula, lampe):1550
Collection of
Collection of a member from FIN Collection of a member from FIN Collection of a member from D |
|
|
|
Forum contributions about this tube
ECL82
Threads: 1 | Posts: 2
|
Hits: 6671 Replies: 1
Limite tension anodique ECL82
|
Michel Deluz
27.Dec.11
|
1
La limitation de 200v anodiques donnée dans la description du tube est une erreur. En montage audio, la penthode de sortie du ECL82 supporte jusqu'à 300V anodique. Elle est proposée par Philips et Mazda montée en push-pull AB avec 250v anodique et 200v de g2 ; dans cette configuration, elle livre 10,5W de puissance de sortie.
Michel Deluz
|
Helmut Kriege
29.Dec.15
|
2
Laut SEL Röhrenbuch, Ausgabe von 1967 ist für die Anoden der Triode und Pentode der ECL82 bis zu 300V erlaubt, für G2 der Pentode ebenfalls.
According to SEL Röhrenbuch, 1967 edition, the anodes of the triode and pentode of the ECL82 are rated up to 300 Volt, same applies to g2 of the pentode.
|
ECL82
End of forum contributions about this tube
You reach this tube or valve page from a search
after clicking the "tubes" tab or by clicking a tube
on a radio model page. You will find thousands
of tubes or valves with interesting links. You
even can look up radio models with a certain tube
line up.
[rmxtube-en]
| Data Compliance |
More Information |
|
|
|
