- Pays
- Royaume Uni
- Fabricant / Marque
- Eddystone (Brand), Stratton and Co., Ltd., Eddystone Radio Ltd.; Birmingham
- Année
- 1962–1970
- Catégorie
- Récepteur commercial (peut inclure bandes amateurs)
- Radiomuseum.org ID
- 109326
Cliquez sur la vignette du schéma pour le demander en tant que document gratuit.
- No. de tubes
- 12
- Principe général
- Super hétérodyne avec étage HF; FI/IF 450 kHz
- Gammes d'ondes
- Bandes en notes
- Tension / type courant
- Alimentation Courant Alternatif (CA) / 110-125; 200-250; Volt
- Haut-parleur
- - Pour casque ou amplificateur BF
- Matière
- Boitier métallique
- De Radiomuseum.org
- Modèle: 940 - Eddystone Brand, Stratton and
- Forme
- Modèle de table profil bas (grand modèle).
- Dimensions (LHP)
- 425 x 222 x 381 mm / 16.7 x 8.7 x 15 inch
- Remarques
- General coverage receiver, 480-1030 kHz / 1,03-2,4 / 2,4-5,4 / 5,4-12,7 / 12,7-30 MHz; AM, SSB (BFO);
S-meter, crystal filter.
- Poids net
- 19.5 kg / 42 lb 15.2 oz (42.952 lb)
- Prix de mise sur le marché
- 153.00 GBP
- Source
- -- Original-techn. papers.
- Auteur
- Modèle crée par d'un membre de A. Voir les propositions de modification pour les contributeurs supplémentaires.
- D'autres Modèles
-
Vous pourrez trouver sous ce lien 255 modèles d'appareils, 125 avec des images et 46 avec des schémas.
Tous les appareils de Eddystone (Brand), Stratton and Co., Ltd., Eddystone Radio Ltd.; Birmingham
Contributions du forum pour ce modèle: Eddystone Brand,: 940
Discussions: 2 | Publications: 2
After using the set for some time, I noticed spurs at several points on the highest frequency range. Some investigation with a hand-held scanner revealed that the ECC189 was oscillating quite strongly at about 60 MHz. Further checks revealed that the problem was also present on the 2.4 - 5.4 MHz range, but I hadn't noticed because aerial noise drowned out the offending spurious responses. They were audible when the aerial was replaced with a 47-Ohm resistor. The spurs on the highest frequency range are also very quickly "tuned through" and may not be noticed.
The ECC189 has a grid stopper, and the grid of the second half of the cascode combination is directly grounded via a number of almost inaccesible capacitors. I am not convinced that these have deteriorated, and suspect that the problem may be caused by my using a different make of ECC189 from that originally in the set. Its also possible that many 940s had this problem from new. None of my ECC189s are Brimar or Mullard.
The problem was solved by using 47 Ohm anode stoppers wired to the wavechange switch as in the attached photo. The performance of the set hasn't changed with these additions. Using a single resistor was considered, and rejected because of the difficulty of accesing the valve base.
Comments invited - Bryce
Pièces jointes
- Eddystone 940 RF Anode Stoppers (45 KB)
Bryce Ringwood, 14.Jun.09
The following may be of interest:
An article in Short Wave Magazine (Aug to October 1988) issues gave instructions for "restoring" (in fact modifying) the Eddystone 940. When purchasing a 940, be aware that it may have been modified and that these changes may not be what you want. The changes to the i.f transformers may be difficult to reverse.
Bryce Ringwood, 13.Jun.08