RF250U/Stereo Ch= CS-200U
Grundig (Radio-Vertrieb, RVF, Radiowerke); Fürth/Bayern
- País
- Alemania
- Fabricante / Marca
- Grundig (Radio-Vertrieb, RVF, Radiowerke); Fürth/Bayern
- Año
- 1967 ?
- Categoría
- Radio - o Sintonizador pasado WW2
- Radiomuseum.org ID
- 73770
-
- alternative name: Grundig Portugal || Grundig USA / Lextronix
GRUNDIG
Haga clic en la miniatura esquemática para solicitarlo como documento gratuito.
- Numero de valvulas
- 8
- Numero de transistores
- Principio principal
- Superheterodino en general; ZF/IF 460/10700 kHz; Modelo de Exportacion
- Número de circuitos sintonía
- 6 Circuíto(s) AM 10 Circuíto(s) FM
- Gama de ondas
- OM, dos OC y FM
- Tensión de funcionamiento
- Red: Corriente alterna (CA, Inglés = AC) / 60Hz, 115 Volt
- Altavoz
- 2 Altavoces
- Potencia de salida
- 5 W (unknown quality)
- Material
- Madera
- de Radiomuseum.org
- Modelo: RF250U/Stereo Ch= CS-200U - Grundig Radio-Vertrieb, RVF,
- Forma
- Sobremesa de botonera.
- Ancho, altura, profundidad
- 22.5 x 12 x 9 inch / 572 x 305 x 229 mm
- Anotaciones
-
Grundig RF250U/Stereo, an export model, is very similar to the domestic model Stereo-Konzertgerät RF160. Build-in Stereo Decoder 6U.
- Peso neto
- 14.5 kg / 31 lb 15 oz (31.938 lb)
- Documentación / Esquemas (1)
- -- Schematic
- Autor
- Modelo creado por Carlos A. Pieroni-García. Ver en "Modificar Ficha" los participantes posteriores.
- Otros modelos
-
Donde encontrará 6208 modelos, 5434 con imágenes y 4203 con esquemas.
Ir al listado general de Grundig (Radio-Vertrieb, RVF, Radiowerke); Fürth/Bayern
Colecciones
El modelo RF250U/Stereo es parte de las colecciones de los siguientes miembros.
Contribuciones en el Foro acerca de este modelo: Grundig Radio-: RF250U/Stereo Ch= CS-200U
Hilos: 1 | Mensajes: 3
Hi ... Can anyone provide alignment instructions for this radio? I have all the original paper work, including schematic, owners manual, etc., and nothing provides info on alignment.
The only thing the schematic says that I think might be related is: "Voltages measured to against chassis with Grundig VTVM. Measuring values valid for MW FM PU without signal on aerial."
So it sounds like you don't need a signal generator -- only a way of measuring the voltage on the pins of the tubes. The schematic does show what these voltages are to be. But what coils are to be adjusted?
Is it possible that this radio is so recent (1968, I think) that it simple does not require alignment?
Any information would be appreciated.
Thanks,
Wes
The only thing the schematic says that I think might be related is: "Voltages measured to against chassis with Grundig VTVM. Measuring values valid for MW FM PU without signal on aerial."
So it sounds like you don't need a signal generator -- only a way of measuring the voltage on the pins of the tubes. The schematic does show what these voltages are to be. But what coils are to be adjusted?
Is it possible that this radio is so recent (1968, I think) that it simple does not require alignment?
Any information would be appreciated.
Thanks,
Wes
Wes Hancher, 25.Jul.08