Beehive 11-4B Ch= 11-4

Kriesler Radio Company; Newtown (Sydney)

Données
Forum
Images
Collections

  • Année
  • 1946–1948
  • Catégorie
  • Radio - ou tuner d'après la guerre 1939-45
  • Radiomuseum.org ID
  • 297564

Cliquez sur la vignette du schéma pour le demander en tant que document gratuit.

 Spécifications techniques

  • No. de tubes
  • 4
  • Principe général
  • Super hétérodyne (en général); FI/IF 455 kHz; Reflex
  • Gammes d'ondes
  • PO et OC
  • Tension / type courant
  • Alimentation Courant Alternatif (CA) / 220-240 Volt
  • Haut-parleur
  • HP dynamique à électro-aimant (électrodynamique)
  • Matière
  • Boitier en bakélite
  • De Radiomuseum.org
  • Modèle: Beehive 11-4B Ch= 11-4 - Kriesler Radio Company;
  • Forme
  • Modèle de table sans poussoirs, modèle cheminée
  • Remarques

  • Kriesler advertised this set & other post-war models as a "Sealed Radio". Solder joints were marked to prevent unauthorised servicing & tampering.

    Walnut Bakelite cabinet. Also available in various colours for 1 Guinea (£1/1/-) extra. Price in WA for standard Walnut model, £19/8/6.

    There are 36 variants of this model:

    • CIRCUIT: As on 11-4 circuit, but with the following alterations:- (Note: Enclosed diagram in lower right hand corner does apply).
    1. Tuning condenser changed from C3 to C95.
    2. Coil Kit changed from No. 15-1 to No. 15-4.
    • COIL KIT: Part No. 15-4 (AWA Tuning Condenser).
    • DIAL GLASSES: Part No. 50-10 (Country stations). Part No. 50-11 (Local stations).
    • SPEAKER: Part No. 70-1 (5" Electro dynamic).
    • OUTPUT TRANSFORMER: Part No. 18-28.
    • POWER TRANSFORMER: Part No. 18-27 (H.T.: 325v. each side of centre tap).

    PROCEDURE FOR REMOVING CHASSIS FROM CABINET:

    1. Remove knobs.
    2. Invert receiver.
    3. Remove base by breaking seal and unscrewing 4 x 3/16" screws in base of cabinet.
    4. Remove 4 x 3/16" nuts, situated in the inside corners of the chassis.
    5. Lay receiver on its back with spindles facing upwards.
    6. Place one hand each side the of chassis. With the forefingers, exert a downward pressure on the front panel, at the same time withdrawing the chassis from the cabinet.

    CHASSIS NUMBERS:

    Every receiver that leaves the Kriesler factory is given two chassis numbers.

    The "Production" chassis number is stamped on a card. The card is riveted to the main chassis in such a location that the number is able to be read without removing the chassis from the cabinet. The "Production" chassis number is the number that should be quoted, together with the model number, when making enquiries.

    The second chassis number (Prefix "0") is stamped into the metal chassis to provide a permanent record.

    Both the abovementioned chassis numbers are recorded at the factory.

  • Prix de mise sur le marché
  • 18.90 AUS £
  • Schémathèque (1)
  • - - Manufacturers Literature (Kriesler Technical Service Instructions.)
  • Auteur
  • Modèle crée par Martin Kent. Voir les propositions de modification pour les contributeurs supplémentaires.

 Collections | Musées | Littérature

 Forum