Beehive 11-4G Ch= 11-4

Kriesler Radio Company; Newtown (Sydney)

Dati
Forum
Immagini
Collezioni

  • Anno
  • 1946–1948
  • Categoria
  • Radio (o sintonizzatore del dopoguerra WW2)
  • Radiomuseum.org ID
  • 297567

Clicca sulla miniatura dello schema per richiederlo come documento gratuito.

 Specifiche tecniche

  • Numero di tubi
  • 4
  • Principio generale
  • Supereterodina (in generale); ZF/IF 455 kHz; Reflex
  • Gamme d'onda
  • Onde medie (OM) e corte (OC).
  • Tensioni di funzionamento
  • Alimentazione a corrente alternata (CA) / 220-240 Volt
  • Altoparlante
  • AP elettrodinamico (bobina mobile e bobina di eccitazione/di campo)
  • Materiali
  • Bachelite
  • Radiomuseum.org
  • Modello: Beehive 11-4G Ch= 11-4 - Kriesler Radio Company;
  • Forma
  • Soprammobile compatto/con bordi arrotondati/midget senza pulsantiera/tastiera.<= 35 cm (Sometimes with handle but for mains only).
  • Annotazioni

  • Kriesler advertised this set & other post-war models as a "Sealed Radio". Solder joints were marked to prevent unauthorised servicing & tampering.

    Walnut Bakelite cabinet. Also available in various colours for 1 Guinea (£1/1/-) extra. Price in WA for standard Walnut model, £19/8/6.

    There are 36 variants of this model:

    • CIRCUIT: As on 11-4 circuit, but with the following alterations:- (Note: Enclosed diagram in lower right hand corner does not apply).
    1. Tone control condenser changed from C74 (0.001 μF) to C27 (0.01 μF). Discard tone control lead to 6V6GT plate. Connect C27 between moving arm of tone control and chassis.
    • COIL KIT: Part No. 15-2 (S.C. Tuning Condenser).
    • DIAL GLASSES: Part No. 50-1 (Country stations). Part No. 50-2 (Local stations).
    • SPEAKER: Part No. 70-1 (5" Electro dynamic).
    • OUTPUT TRANSFORMER: Part No. 18-28.
    • POWER TRANSFORMER: Part No. 18-27 (H.T.: 325v each side of centre tap).

    PROCEDURE FOR REMOVING CHASSIS FROM CABINET:

    1. Remove knobs.
    2. Invert receiver.
    3. Remove base by breaking seal and unscrewing 4 x 3/16" screws in base of cabinet.
    4. Remove 4 x 3/16" nuts, situated in the inside corners of the chassis.
    5. Lay receiver on its back with spindles facing upwards.
    6. Place one hand each side the of chassis. With the forefingers, exert a downward pressure on the front panel, at the same time withdrawing the chassis from the cabinet.

    CHASSIS NUMBERS:

    Every receiver that leaves the Kriesler factory is given two chassis numbers.

    The "Production" chassis number is stamped on a card. The card is riveted to the main chassis in such a location that the number is able to be read without removing the chassis from the cabinet. The "Production" chassis number is the number that should be quoted, together with the model number, when making enquiries.

    The second chassis number (Prefix "0") is stamped into the metal chassis to provide a permanent record.

    Both the abovementioned chassis numbers are recorded at the factory.

  • Prezzo nel primo anno
  • 18.90 AUS £
  • Letteratura / Schemi (1)
  • - - Manufacturers Literature (Kriesler Technical Service Instructions.)
  • Autore
  • Modello inviato da Martin Kent. Utilizzare "Proponi modifica" per inviare ulteriori dati.

 Collezioni | Musei | Letteratura

 Forum