Chiliofono I (1)
Marelli (Radiomarelli); Sesto San Giovanni (MI)
- Pays
- Italy
- Fabricant / Marque
- Marelli (Radiomarelli); Sesto San Giovanni (MI)
- Année
- 1931/1932
- Catégorie
- Radio - ou tuner d'après la guerre 1939-45
- Radiomuseum.org ID
- 73916
Pubblicità Radiomarelli Chiliofono
Cliquez sur la vignette du schéma pour le demander en tant que document gratuit.
- No. de tubes
- 8
- Gammes d'ondes
- PO uniquement
- Particularités
- Tourne disque sans changeur
- Tension / type courant
- Alimentation Courant Alternatif (CA) / 110; 160; 220; 250 Volt
- Haut-parleur
- HP dynamique à électro-aimant (électrodynamique)
- Matière
- Boitier en bois
- De Radiomuseum.org
- Modèle: Chiliofono I - Marelli Radiomarelli; Sesto
- Forme
- Console avec pieds bas < 50% de la hauteur
- Dimensions (LHP)
- 800 x 1100 x 445 mm / 31.5 x 43.3 x 17.5 inch
- Prix de mise sur le marché
- 3,700.00 ITL
- Littérature
- La moderna Supereterodina, Ravalico, 1938 (pag. 371)
- Schémathèque (1)
- -- Original prospect or advert
- Schémathèque (2)
- -- Schematic (La Riparazione degli Apparecchi Radio, Delforno - Colciago, Italy 1941)
- Auteur
- Modèle crée par Alessandro De Poi. Voir les propositions de modification pour les contributeurs supplémentaires.
- D'autres Modèles
-
Vous pourrez trouver sous ce lien 487 modèles d'appareils, 378 avec des images et 300 avec des schémas.
Tous les appareils de Marelli (Radiomarelli); Sesto San Giovanni (MI)
Collections
Le modèle Chiliofono I (1) fait partie des collections des membres suivants.
Contributions du forum pour ce modèle: Marelli Radiomarelli: Chiliofono I
Discussions: 1 | Publications: 1
Dear all,
in the Forum thread ‘Old capacitor marking’ Prof. Dietmar illustrated several non-conventional volume control circuits used in the early age of the radio. This review recalled me the strange solution I found in the model ‘Chiliofono’, produced in Italy by Radiomarelli, in the very late twenties. This huge TRF receiver used a voltage divider, from the screen grid voltage (about 120VDC) to ground, to give a positive bias to the cathodes of the first two RF amplifier stages. The volume control is encircled in the diagram below. Considering the combined action of the cathode currents and of the current flowing from the power supply, the DC voltage on both cathodes roughly varied from 2V to 40V. The result was similar to the grid bias illustrated by Prof. Dietmar in the circuit of Fig. 172, the transconductance of the tubes decreasing when the positive cathode voltage was increased. The relatively high current passing in the volume control potentiometer asked for a wirewound type. By the way, the radio used a double section potentiometer, the second section wired as a variable attenuator on the phono pick-up.
in the Forum thread ‘Old capacitor marking’ Prof. Dietmar illustrated several non-conventional volume control circuits used in the early age of the radio. This review recalled me the strange solution I found in the model ‘Chiliofono’, produced in Italy by Radiomarelli, in the very late twenties. This huge TRF receiver used a voltage divider, from the screen grid voltage (about 120VDC) to ground, to give a positive bias to the cathodes of the first two RF amplifier stages. The volume control is encircled in the diagram below. Considering the combined action of the cathode currents and of the current flowing from the power supply, the DC voltage on both cathodes roughly varied from 2V to 40V. The result was similar to the grid bias illustrated by Prof. Dietmar in the circuit of Fig. 172, the transconductance of the tubes decreasing when the positive cathode voltage was increased. The relatively high current passing in the volume control potentiometer asked for a wirewound type. By the way, the radio used a double section potentiometer, the second section wired as a variable attenuator on the phono pick-up.
Emilio Ciardiello, 21.Nov.07