118B (118, 118A) Tombstone (late)

Philco, Philadelphia Stg. Batt. Co.; USA

  • Anno
  • 1935
  • Categoria
  • Radio (o sintonizzatore del dopoguerra WW2)
  • Radiomuseum.org ID
  • 139836

Clicca sulla miniatura dello schema per richiederlo come documento gratuito.

 Specifiche tecniche

  • Numero di tubi
  • 8
  • Principio generale
  • Supereterodina con stadio RF; ZF/IF 260 kHz
  • Gamme d'onda
  • Onde medie (OM) e corte (OC).
  • Tensioni di funzionamento
  • Alimentazione a corrente alternata (CA) / 115 Volt
  • Altoparlante
  • AP elettrodinamico (bobina mobile e bobina di eccitazione/di campo)
  • Materiali
  • Mobile in legno
  • Radiomuseum.org
  • Modello: 118B [Tombstone ] - Philco, Philadelphia Stg. Batt
  • Forma
  • Soprammobile verticale con decorazioni (Tombstone).
  • Annotazioni
  • The Philco model 118 series is similar to the model 18 series. Both use an 8-tube chassis with shadow meter (tuning aid) and a 10-watt push-pull class A audio output stage. The model 118 series has two bands, BC and SW (4.2 - 12 MHz). Chassis marked "118A" are for 25-40 Hz AC power, while those marked "118" are for 50-60 Hz. The code 123 chassis was used in the chairside model 118RX (see below), while other models most likely used code 121.

    There were nine versions of model 118, each with a different cabinet style. The early version (1934) of the 118B table radio had a cathedral cabinet, with scalloped top edge and a speaker opening with one large and two small openings. The late version (1935) of 118B was a shouldered tombstone.

    There were three highboys: Model 118H (1934-35) had six legs and a Y-shaped speaker grill. The early (1934) and late (1935) versions of the 118D highboy with doors are very similar; both have six legs, but the late version has "waterfall" moulding at the center of the bottom of the main body of the cabinet.

    There were three floor-type consoles: The early version (1934) of the 118X had a classical look, with three round pillars in front of the speaker grill, and patterned moulding around the top of the cabinet. The late version (1935) of 118X was simlar, but had a slightly more modern look overall, and an emblem in the center of the moulding around the top of the cabinet. The 118MX (1934-1935) was a modern-style cabinet, with two square vertical bars in front of the speaker grill.

    The 118RX chairside had a control unit and a large separate speaker cabinet, with the two connected by a 25-foot cable. The controls are located within a T-shaped recess on the top of the control unit cabinet, and the speaker cabinet has a large V pattern with "wings" on the speaker grill.

    A error was found while locating the components for this particular model/chassis. The identification of the components do not match the parts list.

    Part number 28 on the original schematic should be part number 46, which is part of the 4-in-1 condenser can.

    Part number 28 on the schematic should replace part number 29, which is in error. Part 28 is the oscillator compensation condenser according to the parts list. 

    Part 29 is the .003 uf (3000 uuf) mica condenser that is not properly identified on the original schematic.

    See the corrected section of the schematic that was in error.

  • Prezzo nel primo anno
  • 70.00 $
  • Riferimenti schemi
  • Rider's Perpetual, Volume 5 = ca. 1934 and before
  • Letteratura / Schemi (1)
  • Philco Service Bulletin # 194
  • Autore
  • Modello inviato da Thomas Albrecht. Utilizzare "Proponi modifica" per inviare ulteriori dati.

 Collezioni | Musei | Letteratura

 Forum