• Country
• Germany

• Manufacturer / Brand
• Philips Radios - Deutschland

• Year
• 1981/1982

• Category
• Service- or Lab Equipment

• Radiomuseum.org ID
• 138919

• • Brand: Deutsche Philips-Ges.

Click on the schematic thumbnail to request the schematic as a free document.

• Number of Transistors
• 5

• Semiconductors
• BF195 BF195 BF195 BC148 BC148 1N4001

• Wave bands
• - without

• Power type and voltage
• Dry Batteries / 9 Volt

• Loudspeaker
• - - No sound reproduction output.

• Material
• Bakelite or Plastics (type unknown)

• from Radiomuseum.org
• Model: Multi-Signalgeber SIM212 - Philips Radios - Deutschland

• Dimensions (WHD)
• 190 x 30 x 35 mm / 7.5 x 1.2 x 1.4 inch

• Notes

• Handlicher Signalgenerator zur Fehlersuche in NF-Verstärkern, RF-, SW- und FFS-Geräten mit Sinusoszillator, 4,43/5,5 MHz umschaltbar. Modulation mit 300-Hz-Rechteckschwingung aus Multivibrator.

  ---

  SlGNAL INJECTOR, Type SIM-212 Code: 4822 395 30066

  Description:

  With the aid of this signal injector faults can be quickly located both in L.F. amplifiers and in radio, black-and white and colour-TV receivers. The injector contains a sine-wave oscillator which on delivery is tuned to the frequencies 5.5 MHz and 4.43 MHz.
  This oscillator is modulated with the aid of a multivibrator supplying a square-wave voltage with a frequency of approx. 300 Hz. The output voltages of the injector can be varied continuously by means of one control.

  Putting the injector into service

  - For changing over to other frequencies, see " adjusting the injector".
  - For the high frequencies 5.5 MHz and 4.43 MHz the test probe must be inserted into socket ∿∿ for the low frequency into socket ∿.
  - Set switch F1 - F2 (B) to position F1 for 4.43 MHz and to position F2 for 5.5 MHz.
  - Now inject the signal selected on the appropriate spot in the unit to be repaired (connect the earth lead to the chassis).
  - Push the button for switching on the injector (D) .
  - With the aid of control (A) the intensity of the signal can be varied.
  - lf the 300-Hz signal should have to be injected (test probe in position ∿ ), the position of switch F1 - F2 is irrelevant.

  The H.F. signals can be used for tracing faults in:

  - The audio I.F. section of black-and-white and colour-TV receivers (F2 : 5,5 MHz).
  - The video I.F. section and channel selectors of black & white and colour-TV receivers (harmonics of F1 – 5.5 MHz or F2 – 4.43 MHz).

  Adjustment of the injector:

  E.g. the injector must be adjusted for SECAM:
  - lnterconnect F. and G.
  - Set control A to maximum signal.
  - Set the injection pin to positions ∿∿ (H.F.).
  - Set switch F1 - F2 to position F1.
  - Inject a signal into the input of the sound I.F. section of a television receiver.
  - Adjust the care of coil L 1 to maximum signal.
  - Set switch F1 - F2 to position F2.
  - lnject a signal into the input of the first I.F. section (output of channel selector) and adjust C7 to maximum picture (turn the control A slowly back during adjusting, so that the picture is on the verge of showing noise).
  The same adjusting method can be used for the other systems.

• Net weight (2.2 lb = 1 kg)
• 0.2 kg / 0 lb 7 oz (0.441 lb)

• Source of data
• - - Manufacturers Literature

• Author
• Model page created by a member from D. See "Data change" for further contributors.

• Other Models

• Here you find 2543 models, 2255 with images and 1564 with schematics for wireless sets etc. In French: TSF for Télégraphie sans fil.
  All listed radios etc. from Philips Radios - Deutschland