Matador V6A, V6A -06, V6A -20

Philips; Eindhoven (tubes international!); Miniwatt

Données
Forum
Images
Collections

  • Année
  • 1937/1938
  • Catégorie
  • Radio - ou tuner d'après la guerre 1939-45
  • Radiomuseum.org ID
  • 80979

Cliquez sur la vignette du schéma pour le demander en tant que document gratuit.

 Spécifications techniques

  • No. de tubes
  • 5
  • Principe général
  • Super hétérodyne (en général); FI/IF 128 kHz; 2 Etage(s) BF
  • Circuits accordés
  • 7 Circuits MA (AM)
  • Gammes d'ondes
  • PO, GO et OC
  • Tension / type courant
  • Alimentation Courant Alternatif (CA) / 110; 125; 145; 200; 220; 245 Volt
  • Haut-parleur
  • HP dynamique à aimant permanent + bobine mobile / Ø 20 cm = 7.9 inch
  • Matière
  • Boitier en bakélite
  • De Radiomuseum.org
  • Modèle: Matador V6A, V6A -06, V6A -20 - Philips; Eindhoven tubes
  • Forme
  • Modèle de table profil bas (grand modèle).
  • Remarques
  • 3 Band reception:
    • LW: 725 - 1975 m.
    • BC: 198 - 585 m.
    • SW: 16,7 - 51 m.
    Tuning scale light bulbs type: 8042 (4V, 500mA).
    Loudspeaker Philips type 9619. There are no connectors for a second loudspeaker or pick-up. 
     
    The differences between V6A, V6A -06 and V6A -20 are minimal and described in the technical manual
  • Schémathèque (1)
  • -- Original-techn. papers.
  • Auteur
  • Modèle crée par d'un membre de D. Voir les propositions de modification pour les contributeurs supplémentaires.

 Collections | Musées | Littérature

Collections

Le modèle Matador fait partie des collections des membres suivants.

Musées

Le modèle Matador peut être vu dans les musées suivants.

Littérature

Le modèle Matador est documenté dans la littérature suivante.

 Forum

Contributions du forum pour ce modèle: Philips; Eindhoven: Matador V6A, V6A -06, V6A -20

Discussions: 4 | Publications: 18

Dear friends, on several occasions I came across to one IF coil of this model interrupted.
So I decided to go in to one of these parts and made a reverse engineering on it. The result is shown in attached picture.
I hope that helps with your "Matador" restoration
I think that will fit to the model variations too like Pioneiro V6, Junior V6, Junior V6A and Obertura V6.
 

Greetings

Meyer

Pièces jointes

Meyer Rochwerger, 27.Feb.12

Weitere Posts (1) zu diesem Thema.

Gentlemen My Philips Matador V6A is now in an excellent working condition. There was more job than expected when I had to replace a lot of the cabeling since the rubber isolation had dried so badly that it fell off when touching. But the most important operation was to replace the tar condensers for the IF-filters and this resulted even to replace the tubular ceramic wirewounded capacitors with variable 6-40 pF ones. Since my signal generator (an old Heathkit ) do not go down the IF frequenxy (128 kHz) I had to use my home made function generator and the oscilloscope to ahcieve the peak IF. Oh boy, what a receiver to be 70 years old (I mentioned before it was 80 but the smart reader obviously noticed my miscalculation), its selectivity and sensitivity is excellent although the stability is not so good but it is not an object for everyday use either. Now there's only one thing left to do with the V6A, thats how to get the bakelite shiny and I think this is not the easiest job. Anyway, thanks a lot for your support and advices. The next project is waiting already on the table. Regards Lars-G.

Lars-G. Lundelin, 11.Feb.07

Weitere Posts (9) zu diesem Thema.

Dear Radio friends! When restoring my Philips 6VA I found that the power smoothing capacitors didn't come up to the rates according to the schematics. Well, when I unsoldered the dropping resistor (R2, 2k Ohm) it was damaged and I'd to renew it. This resistor is a quite big one (in fact 3 R:s in paralell)) and is probably wire wounded. Doe’s this wire wounded resistor make any sense to the +B rail when considering the inductive reactance, or does it act like a choke too? Regards Lars-G.

Lars-G. Lundelin, 03.Feb.07

Weitere Posts (4) zu diesem Thema.

Hello Radio friends! Trying to restore my newly acquired Philips Matador II V6A but I can't find out how to tune the IF-filters because the trimmer capacitors (as they suppose to be according to the schematics) do not have any facilities for that. Attaching a pic of the second IF-filter with caps arrowed. The caps are tubular ceramics and are wire wouded as can be seen from the picture. Any suggestions would be appreciated. Kind Regards Lars-G.

Lars-G. Lundelin, 23.Jan.07

Weitere Posts (4) zu diesem Thema.