66X3 Ch= RC-1038

RCA (RCA Victor Co. Inc.); New York (NY)

Daten
Forum
Bilder
Sammlungen

  • Jahr
  • 1946
  • Kategorie
  • Rundfunkempfänger (Radio - oder Tuner nach WW2)
  • Radiomuseum.org ID
  • 53657
    • anderer Name: RCA Manufacturing || Victor Talking Machine

Klicken Sie auf den Schaltplanausschnitt, um diesen kostenlos als Dokument anzufordern.

 Technische Daten

  • Anzahl Röhren
  • 6
  • Hauptprinzip
  • Super mit HF-Vorstufe; ZF/IF 455 kHz
  • Wellenbereiche
  • Mittelwelle und Kurzwelle.
  • Betriebsart / Volt
  • Allstromgerät / 105-125 Volt
  • Lautsprecher
  • Dynamischer (permanent) Ovallautsprecher / Ø 6 inch = 15.2 cm
  • Belastbarkeit / Leistung
  • 1.5 W (Qualität unbekannt)
  • Material
  • Gerät mit Holzgehäuse
  • von Radiomuseum.org
  • Modell: 66X3 Ch= RC-1038 - RCA RCA Victor Co. Inc.; New
  • Form
  • Tischgerät-gross, - Querformat (breiter als hoch oder quadratisch).
  • Abmessungen (BHT)
  • 15.3 x 9.3 x 7.3 inch / 389 x 236 x 185 mm
  • Bemerkung
  • Pilot lamp: Mazda Nº 1490, 3.2V.
  • Datenherkunft extern
  • Ernst Erb
  • Schaltungsnachweis
  • Rider's Perpetual, Volume 15 = 1947 and before
  • Literatur/Schema (1)
  • RCA Victor Instruments Service Notes 1946

 Sammlungen | Museen | Literatur

Sammlungen

Das Modell 66X3 befindet sich in den Sammlungen folgender Mitglieder.

 Forum

Forumsbeiträge zum Modell: RCA RCA Victor Co.: 66X3 Ch= RC-1038

Threads: 1 | Posts: 7

I recently purchased an RCA 66X3 AM/SW reciever from eBay. It initially had the normal bad capacitors and several >20% out of tolerance resistors. Tubes tested OK with perhaps the RF amp (12SG7) a little weak but good. Tune up seemed to go OK, but the SW band was definitely poor with a lot of extraneous mixes on the dial that appeared to be from nearby FM stations. Sensitivity and volume was very low.

I have a battery operated o'scope and discovered that the LO seemed to be on the AVC circuits and on the circuit ground of the 12SQ7 resulting in LO on the plate of the RF amp. This situation only exists while in SW. The regular AM broadcast band is actually quite good and there is no LO on the RF amp or AVC.

I am wondering if anyone else has experienced this problem and what they did to correct it. I have had some emails with other less technical owners and they state that their sets are also weak on SW but I don't have any information on strange mixes in their sets.

Update: I found that bypassing the circuit ground of the 12SG7 (B-) to chassis did not affect the level of LO signal on the plate. LO signal on the pin 8 (signal in) of the 12AS7 (mixer) is 180° out of phase with the LO on pin 5 (osc). This must have something to do with the band switch, but contacts appear to be OK. The band switch shorts out a section of the oscillator coil to B- rather than switching in a different coil. B- comes to the bandswitch via an insulated braided cable (like the shield off of a piece of coax) and LO (12mHz) signal can be seen on the cable. Once the LO signal is coupled onto the AVC circuit, it is present on the grid of the 12SG7 (RF amp) which makes this one of those "chicken or egg" questions. 

Fred Neudecker, 02.Dec.13

Weitere Posts (7) zu diesem Thema.