• Jahr
  • 2014 ?
  • Kategorie
  • Bausatz, Baukasten oder Bauanleitung (Kit)
  • Radiomuseum.org ID
  • 302481

Klicken Sie auf den Schaltplanausschnitt, um diesen kostenlos als Dokument anzufordern.

 Technische Daten

  • Anzahl Transistoren
  • 3
  • Hauptprinzip
  • Superhet allgemein; ZF/IF 455 kHz
  • Wellenbereiche
  • Mittelwelle, keine anderen.
  • Betriebsart / Volt
  • Trockenbatterien / AA: 2 x 1.5 Volt
  • Lautsprecher
  • Dynamischer LS, keine Erregerspule (permanentdynamisch) / Ø 7 cm = 2.8 inch
  • Belastbarkeit / Leistung
  • 0.12 W (max./spitze)
  • Material
  • Plastikgehäuse (nicht Bakelit), Thermoplast
  • von Radiomuseum.org
  • Modell: 2P3 - Tecsun 德生通用电器制造有限公...
  • Form
  • Kleines Reisegerät oder «Taschengerät» < 20 cm.
  • Abmessungen (BHT)
  • 110 x 75 x 35 mm / 4.3 x 3 x 1.4 inch
  • Bemerkung
  • The original 2P3 diy kit radio was developed in the mid 1960's. This is the new 2014 2P3 diy kit radio, retaining the old style case but with updated chassis and components.

    The Chinese building guide is comprehensive and detailed, incuding a very detailed section on how to align the radio to get the maximum signal possible. There is a  publicly available English translation made by CRKITS covering the 2014.3 Ver. 4 "Green PCB" variant. That said, this is not an electronics beginner's kit..

    Main features

    • Frequency coverage: MW 530 - 1620 kHz
    • Sensitivity: < 1 mV/m
    • Maximum audio output: 120 mW
    • Quiescent current: 7 mA

    Some technical details

    The RF section is handled by three silicon transistors, the detection is handled by a germanium 1N60 diode, and the audio uses one CD7368 IC.

    Q1 is the RF amplifier/mixer/oscillator, and Q2 and Q3 supports the two IF stages where a 455 kHz ceramic filter helps improving the selectivity, besides the three canned RF transformers (one oscillator in red, one 1st IF in yellow, and one 3rd IF in black).

    The ferrite antenna uses three coil configuration to allow fine adjustment for maximum signal reception on both low and high RF frequencies.

    The detection circuit built around the 1N60 diode is shielded.

    The power supply lines are RC decoupled for a total of three Vcc lines, where the 3rd line at 1.7VDC used to bias the RF transistors is stabilized with three 1N4148 diodes in series.

    The three RF transistor collector Vcc lines (marked as A, B, C, in the diagram) comes in open circuit in the PCB to allow for current checking and test for build errors. These test points need to be short-circuited with solder in order to have a fully functional circuit.

     

  • Originalpreis
  • 35.00 USD
  • Autor
  • Modellseite von Didier Tholomier angelegt. Siehe bei "Änderungsvorschlag" für weitere Mitarbeit.

 Sammlungen | Museen | Literatur

Sammlungen

Das Modell befindet sich in den Sammlungen folgender Mitglieder.

 Forum

Forumsbeiträge zum Modell: Tecsun 德生通用电器...: 2P3

Threads: 1 | Posts: 1

This is a English translation from the original Chinese building instructions for the checking and adjusting procedures.

I have used a OCR tool to extract the Chinese text from the public available pictures of the building instructions and then used Google to help with the translation.

Jose Mesquita, 10.Sep.21

Weitere Posts (1) zu diesem Thema.