Concertino 2194 poliert

Telefunken Deutschland (TFK), (Gesellschaft für drahtlose Telegraphie Telefunken mbH

Daten
Forum
Bilder
Sammlungen

  • Jahr
  • 1960–1962
  • Kategorie
  • Rundfunkempfänger (Radio - oder Tuner nach WW2)
  • Radiomuseum.org ID
  • 23866

Klicken Sie auf den Schaltplanausschnitt, um diesen kostenlos als Dokument anzufordern.

 Technische Daten

  • Anzahl Röhren
  • 9
  • Anzahl Transistoren
  • Hauptprinzip
  • Superhet allgemein; ZF/IF 460/10700 kHz
  • Anzahl Kreise
  • 6 Kreis(e) AM     12 Kreis(e) FM
  • Wellenbereiche
  • Langwelle, Mittelwelle, Kurzwelle und UKW.
  • Betriebsart / Volt
  • Wechselstromspeisung / 110, 125, 220, 240 Volt
  • Lautsprecher
  • 4 Lautsprecher
  • Material
  • Gerät mit Holzgehäuse

Die GFGF Zeitschrift Funkgeschichte bringt interessante Artikel zu Radios, Funkwesen und Medien. Bei Radiomuseum.org finden Sie die vollständigen Hefte früherer Ausgaben als PDF zum Download.

  • von Radiomuseum.org
  • Modell: Concertino 2194 [poliert] - Telefunken Deutschland TFK,
  • Form
  • Tischgerät, Tasten oder Druckknöpfe.
  • Abmessungen (BHT)
  • 640 x 375 x 270 mm / 25.2 x 14.8 x 10.6 inch
  • Bemerkung

  • Stereo-NF-Verstärker, 7-W-Gegentakt-Endstufe in Zweiwegtechnik.
    AFC wird aktiv beim Loslassen des Abstimmknopfes.

    Parallelgerät zum AEG Tambour 61.

  • Nettogewicht
  • 14.3 kg / 31 lb 8 oz (31.498 lb)
  • Originalpreis
  • 459.00 DM
  • Datenherkunft extern
  • Erb
  • Literatur/Schema (1)
  • -- Original-techn. papers.

 Sammlungen | Museen | Literatur

Sammlungen

Das Modell Concertino befindet sich in den Sammlungen folgender Mitglieder.

Museen

Das Modell Concertino ist in den folgenden Museen zu sehen.

 Forum

Forumsbeiträge zum Modell: Telefunken: Concertino 2194

Threads: 3 | Posts: 24

 

Hello,

I have just overhauled a 1961 Telefunken Concertino 2194 and I have a question about its AM IF frequency.  It's currently set to around 480kHz, some way off the 460kHz stated in the service manual but I don't think the set has been tampered with. Stamped on one of the IF transformers is '485kHz', which may suggest that for the UK and other export markets it was changed. Is it likely that the AM IF frequency on exported versions of this set would be set to 485kHz?  I have overhauled several German built radios of this era and the AM IF frequency has always been the same as the German market sets.

If so I shall align it to 485kHz as it has drifted and the set is lacking a little gain on all AM bands.

Regards ............ Howard

Surrey Hills, England

 

 

 

Howard Craven, 04.Feb.14

Weitere Posts (4) zu diesem Thema.

 This model has a stereo audio circuit.  From studying the schematic, it seems to have an extra triode in the left channel.  After the volume control, the audio signal for each channel goes through through a triode.  In the case of the left channel, that triode is part of the EABC80 and in the case of the right channel the triode is part of the ECL86.  The output of the right channel triode goes directly to the pentode section of the ECL86.  The left channel, however, goes through the triode section of the ECL86 before it is applied to the pentode section.  

I have two questions concerning this model.

  1. Why the extra stage in the left channel?
  2. How to adjust W66, the 20k trim potentiometer in the cathode circuit of the second triode of the left channel?

Best Regards, Jim

Improved because the circuit diagram was too large.

James MacWilliams, 12.Apr.10

Weitere Posts (4) zu diesem Thema.

I am restoring a Telefunken Concertino 2194.  I have replaced all the paper capacitors and a couple of resistors that were out of tolerance.  The radio works well on all the AM bands - LW, MW, and KW -- and sounds great.  FM (or UKW), however, is not working.  It does receive one station, extremely weak, volume has to be at maximum to hear it.  This station is just outside the FM band the radio should receive -- 101.0 MHz.

All the voltages are okay.  I have checked the waveband keyboard switches and they are okay.  I have tried known good tubes (valves) -- ECC85, EF89 (2x), ECH81, and EABC80 with no change.

I have made some DC resistance checks through the FM front end section with the ECC85 removed to verify the resistors.  They are okay with the exception of W604 which should be 33k and I measure 21k.  But I am not sure how to open the front end section, so nothing has been changed (or cleaned for that matter).

I am hoping for some suggestions on where to procede.  Or perhaps notes on how to open and service the FM front end.  Has anyone had similar problems with this model?  Any guidance would be appreciated.  Regards,  Jim

James MacWilliams, 07.Jul.09

Weitere Posts (16) zu diesem Thema.