Concertino 2194 poliert
Telefunken Deutschland (TFK), (Gesellschaft für drahtlose Telegraphie Telefunken mbH
- País
- Alemania
- Fabricante / Marca
- Telefunken Deutschland (TFK), (Gesellschaft für drahtlose Telegraphie Telefunken mbH
- Año
- 1960–1962
- Categoría
- Radio - o Sintonizador pasado WW2
- Radiomuseum.org ID
- 23866
Haga clic en la miniatura esquemática para solicitarlo como documento gratuito.
- Numero de valvulas
- 9
- Numero de transistores
- Principio principal
- Superheterodino en general; ZF/IF 460/10700 kHz
- Número de circuitos sintonía
- 6 Circuíto(s) AM 12 Circuíto(s) FM
- Gama de ondas
- OM, OL, OC y FM
- Tensión de funcionamiento
- Red: Corriente alterna (CA, Inglés = AC) / 110, 125, 220, 240 Volt
- Altavoz
- 4 Altavoces
- Material
- Madera
- de Radiomuseum.org
- Modelo: Concertino 2194 [poliert] - Telefunken Deutschland TFK,
- Forma
- Sobremesa de botonera.
- Ancho, altura, profundidad
- 640 x 375 x 270 mm / 25.2 x 14.8 x 10.6 inch
- Anotaciones
-
Stereo-NF-Verstärker, 7-W-Gegentakt-Endstufe in Zweiwegtechnik.
AFC wird aktiv beim Loslassen des Abstimmknopfes.Parallelgerät zum AEG Tambour 61.
- Peso neto
- 14.3 kg / 31 lb 8 oz (31.498 lb)
- Precio durante el primer año
- 459.00 DM
- Ext. procedencia de los datos
- Erb
- Procedencia de los datos
- HdB d.Rdf-& Ferns-GrH 1961/62
- Documentación / Esquemas (1)
- -- Original-techn. papers.
- Otros modelos
-
Donde encontrará 3554 modelos, 3137 con imágenes y 2099 con esquemas.
Ir al listado general de Telefunken Deutschland (TFK), (Gesellschaft für drahtlose Telegraphie Telefunken mbH
Colecciones
El modelo Concertino es parte de las colecciones de los siguientes miembros.
Museos
El modelo Concertino se puede ver en los siguientes museos.
Contribuciones en el Foro acerca de este modelo: Telefunken: Concertino 2194
Hilos: 3 | Mensajes: 24
Hello,
I have just overhauled a 1961 Telefunken Concertino 2194 and I have a question about its AM IF frequency. It's currently set to around 480kHz, some way off the 460kHz stated in the service manual but I don't think the set has been tampered with. Stamped on one of the IF transformers is '485kHz', which may suggest that for the UK and other export markets it was changed. Is it likely that the AM IF frequency on exported versions of this set would be set to 485kHz? I have overhauled several German built radios of this era and the AM IF frequency has always been the same as the German market sets.
If so I shall align it to 485kHz as it has drifted and the set is lacking a little gain on all AM bands.
Regards ............ Howard
Surrey Hills, England
Howard Craven, 04.Feb.14
This model has a stereo audio circuit. From studying the schematic, it seems to have an extra triode in the left channel. After the volume control, the audio signal for each channel goes through through a triode. In the case of the left channel, that triode is part of the EABC80 and in the case of the right channel the triode is part of the ECL86. The output of the right channel triode goes directly to the pentode section of the ECL86. The left channel, however, goes through the triode section of the ECL86 before it is applied to the pentode section.
I have two questions concerning this model.
- Why the extra stage in the left channel?
- How to adjust W66, the 20k trim potentiometer in the cathode circuit of the second triode of the left channel?
Best Regards, Jim
Improved because the circuit diagram was too large.
James MacWilliams, 12.Apr.10
I am restoring a Telefunken Concertino 2194. I have replaced all the paper capacitors and a couple of resistors that were out of tolerance. The radio works well on all the AM bands - LW, MW, and KW -- and sounds great. FM (or UKW), however, is not working. It does receive one station, extremely weak, volume has to be at maximum to hear it. This station is just outside the FM band the radio should receive -- 101.0 MHz.
All the voltages are okay. I have checked the waveband keyboard switches and they are okay. I have tried known good tubes (valves) -- ECC85, EF89 (2x), ECH81, and EABC80 with no change.
I have made some DC resistance checks through the FM front end section with the ECC85 removed to verify the resistors. They are okay with the exception of W604 which should be 33k and I measure 21k. But I am not sure how to open the front end section, so nothing has been changed (or cleaned for that matter).
I am hoping for some suggestions on where to procede. Or perhaps notes on how to open and service the FM front end. Has anyone had similar problems with this model? Any guidance would be appreciated. Regards, Jim
James MacWilliams, 07.Jul.09